This binding integrates BTicino / Legrand MyHOME® BUS and Zigbee wireless (MyHOME_Play®) devices using the [OpenWebNet](https://en.wikipedia.org/wiki/OpenWebNet) protocol.
[F453](https://www.homesystems-legrandgroup.com/home?p_p_id=it_smc_bticino_homesystems_search_AutocompletesearchPortlet&p_p_lifecycle=0&p_p_state=normal&p_p_mode=view&_it_smc_bticino_homesystems_search_AutocompletesearchPortlet_journalArticleId=2703566&_it_smc_bticino_homesystems_search_AutocompletesearchPortlet_mvcPath=%2Fview_journal_article_content.jsp), etc.
**NOTE** The new BTicino Living Now® and Livinglight Smart® wireless systems are not supported by this binding as they do not use the OpenWebNet protocol.
| Temperature Control | `4` | `bus_thermo_zone`, `bus_thermo_sensor`, `bus_thermo_cu` | Thermo zones management and temperature sensors (probes) | Successfully tested: H/LN4691, HS4692, KG4691; thermo sensors: L/N/NT4577 + 3455; Central Units (4 or 99 zones) are not fully supported yet. See [Channels - Thermo](#configuring-thermo) for more details |
| Alarm | `5` | `bus_alarm_system`, `bus_alarm_zone` | BUS Alarm system and zones | Successfully tested: Burglar-alarm Unit 3486 |
| Auxiliary (AUX) | `9` | `bus_aux` | AUX commands | Successfully tested: AUX configured for Burglar-alarm Unit 3486. **Only sending AUX commands is supported** |
| Dry Contact and IR Interfaces | `25` | `bus_dry_contact_ir` | Dry Contacts and IR Interfaces | Successfully tested: contact interfaces F428 and 3477; IR sensors: HC/HD/HS/L/N/NT4610 |
| Energy Management | `18` | `bus_energy_meter` | Energy Management | Successfully tested: F520, F521. Partially tested: F522, F523 |
- BUS Gateway automatic discovery will work only for newer gateways supporting UPnP: F454, MyHOMEServer1, MH201, MH202, MH200N, MyHOME_Screen 10.
For other gateways you can add them manually, see [Thing Configuration](#thing-configuration) below.
- After gateway is discovered and added a connection with default password (`12345`) is tested first: if it does not work the gateway will go offline and an error status will be set. A correct password must then be set in the gateway Thing configuration otherwise the gateway will not become online.
- Basic Scenario modules and CEN/CEN+ Scenario Control devices will be discovered by activation only. See [discovery by activation](#discovery-by-activation) for details. After confirming a discovered CEN/CEN+ scenario device from Inbox, activate again its buttons to add button channels automatically
BUS devices can also be discovered if they are activated while an Inbox Scan has been started: start a new Scan, wait 15-20 seconds and then _while the Scan is still active_, activate the physical device (for example dim the dimmer) to have it discovered by the binding.
Setting the parameter `discoveryByActivation=true` for a BUS gateway Thing makes discovery by activation always working also when an Inbox Scan hasn't been started.
- _**IMPORTANT NOTE:**_ As for other openHAB bindings using the USB/serial ports, on Linux the `openhab` user must be member of the `dialout` group to be able to use USB/serial port; set the group with the following command:
- The user will need to logout and login to see the new group added. If you added your user to this group and still cannot get permission, reboot Linux to ensure the new group permission is attached to the `openhab` user.
- Once the Zigbee USB Gateway is added and online, a second Inbox Scan will discover devices connected to it. Because of the Zigbee radio network, device discovery will take ~40-60 sec. Be patient!
- Wireless devices must be part of the same Zigbee network of the Zigbee USB Gateway to discover them. Please refer to [this video by BTicino](https://www.youtube.com/watch?v=CoIgg_Xqhbo) to setup a Zigbee wireless network which includes the Zigbee USB Gateway
- Only powered wireless devices part of the same Zigbee network and within radio coverage of the Zigbee USB Gateway will be discovered. Unreachable or not powered devices will be discovered as _GENERIC_ devices and cannot be controlled
- Wireless control units cannot be discovered by the Zigbee USB Gateway and therefore are not supported
-`host` : IP address / hostname of the BUS/SCS gateway (`String`, _mandatory_)
- Example: `192.168.1.35`
-`port` : port (`int`, _optional_, default: `20000`)
-`passwd` : gateway password (`String`, _required_ for gateways that have a password. Default: `12345`)
- Example: `abcde` or `12345`
- if the BUS/SCS gateway is configured to accept connections from the openHAB computer IP address, no password should be required
- in all other cases, a password must be configured. This includes gateways that have been discovered and added from Inbox: without a password configured they will remain OFFLINE
-`discoveryByActivation`: discover BUS devices when they are activated also when a device scan hasn't been started from Inbox (`boolean`, _optional_, default: `false`). See [Discovery by Activation](#discovery-by-activation).
- the associated gateway Thing (`Parent Bridge` menu)
- the `where` configuration parameter (`OpenWebNet Address`): this is the OpenWebNet address configured for the device in the BTicino/Legrand system. This address can be found either on the device itself (Physical configuration, using jumpers in case of BUS) or through the MyHOME_Suite software (Virtual configuration). The address can have several formats depending on the device/system:
- example for Zigbee devices: `where=765432101#9`. The ID of the device (ADDR part) is usually written in hexadecimal on the device itself, for example `ID 0074CBB1`: convert to decimal (`7654321`) and add `01#9` at the end to obtain `where=765432101#9`. For 2-unit switch devices (`zb_on_off_switch2u`), last part should be `00#9`.
In BTicino MyHOME Thermoregulation (WHO=4) each **zone** has associated a thermostat, additional temperature sensors (optional), actuators and heating/conditioning valves. A zone is associated to at least one thermostat and one actuator.
Thermo zones can be configured defining a `bus_thermo_zone` Thing for each zone with the following parameters:
- the `standAlone` configuration parameter (`boolean`, default: `true`): identifies if the zone is managed or not by a Central Unit (4 or 99 zones). `standAlone=true` means no Central Unit is present in the system.
The (optional) Central Unit can be configured defining a `bus_themo_cu` Thing with the `where` configuration parameter (`OpenWebNet Address`) set to `where="0"`.
The BTicino Alarm system **cannot** be controlled directly via the OpenWebNet protocol: the only possibility is to use AUX commands and configure your Burglar-alarm Unit (`Automations` section) to execute some commands (e.g. Arm alarm) when it receives a particular AUX OpenWebNet command.
Alarm Automations allow you to run an OpenWebNet command when a particular event occurs; in this case, the events are changes of state of the AUX device (WHO=9) and the command to be performed is a burglar alarm command (WHO=5).
| `switch` or `switch_01`/`02` for Zigbee | `bus_on_off_switch`, `zb_on_off_switch`, `zb_on_off_switch2u` | Switch | To switch the device `ON` and `OFF` | R/W |
| `sensor` | `bus_dry_contact_ir` | Switch | Indicates if a Dry Contact Interface is `ON`/`OFF`, or if an IR Sensor is detecting movement (`ON`), or not (`OFF`) | R |
| `temperature` | `bus_thermo_zone`, `bus_thermo_sensor` | Number:Temperature | The zone currently sensed temperature | R | N |
| `setpointTemperature` | `bus_thermo_zone`, `bus_thermo_cu` | Number:Temperature | The zone or Central Unit setpoint temperature | R/W | N |
| `function` | `bus_thermo_zone`, `bus_thermo_cu` | String | The zone set thermo function (`COOLING`, `HEATING`, `GENERIC`) or the Central Unit thermo function (`COOLING`, `HEATING`) | R/W | N |
| `mode` | `bus_thermo_zone`, `bus_thermo_cu` | String | The zone set mode (`MANUAL`, `PROTECTION`, `OFF`) or the Central Unit set mode ( `MANUAL`, `PROTECTION`, `OFF`, `WEEKLY`, `SCENARIO`) | R/W | N |
| `speedFanCoil` | `bus_thermo_zone` | String | The zone fancoil speed: `AUTO`, `SPEED_1`, `SPEED_2`, `SPEED_3` | R/W | N |
For Percent commands and position feedback to work correctly, the `shutterRun` Thing config parameter must be configured equal to the time (in ms) to go from full UP to full DOWN. It's possible to enter a value manually or set `shutterRun=AUTO` (default) to calibrate `shutterRun` automatically.
_Automatic calibration of `shutterRun`_
If `shutterRun` is set to AUTO a _UP >> DOWN >> Position%_ cycle will be performed automatically the first time a Percent command is sent to the shutter. The binding then relies on the _STOP_ command sent by the actuator at the stop time set in the actuator's advanced configuration in the My Home Suite. Therefore the binding's automatic calibration of `shutterRun` only works correctly if the stop time is set to the time the shutters need to go from full UP to full DOWN.
Older actuators that come without an ID and do not support advanced configuration via the My Home Suite have a fixed stop time of 60 seconds. In this case auto calibration of the binding cannot be used and `shutterRun` has to be set manually.
- if `shutterRun` is not set, or is set to `AUTO` but calibration has not been performed yet, then position estimation will remain `UNDEF` (undefined)
- if `shutterRun` is wrongly set higher than the actual runtime, then position estimation will remain `UNDEF`: try to reduce shutterRun until you find the right value
- before adding/configuring roller shutter Things it is suggested to have all roller shutters `UP`, otherwise the Percent command won’t work until the roller shutter is fully rolled up
- if OH is restarted the binding does not know if a shutter position has changed in the meantime, so its position will be `UNDEF`. Move the shutter all `UP`/`DOWN` to synchronize again its position with the binding
Basic Scenarios and CEN/CEN+ Scenarios channels are [TRIGGER channels](https://www.openhab.org/docs/configuration/rules-dsl.html#channel-based-triggers]): they handle events and do not have a state.
A powerful feature is to detect scenario activations and CEN/CEN+ buttons press events to trigger rules in openHAB: this way openHAB becomes a very powerful scenario manager activated by BTicino scenario control modules or by CEN/CEN+ scenarios physical buttons.
It's also possible to send _virtual scenario activation_ and _virtual press_ events on the BUS, for example to enable the activation of MH202 or F420 scenarios from openHAB..
See [openwebnet.sitemap](#openwebnetsitemap) & [openwebnet.rules](#openwebnetrules) sections for examples on how to use the `activateScenario` and `virtualPress` actions connected to a pushbutton on a sitemap.
- basic scenario channels are named `scenario` and possible events are: `SCENARIO_01` ... `SCENARIO_16` (or up to `SCENARIO_20` in case of module IR3456) when a scenario is activated
- CEN/CEN+ channels are named `button#X` where `X` is the button number on the CEN/CEN+ Scenario Control device
- in the .thing file configuration you can specify the `buttons` parameter to define a comma-separated list of buttons numbers [0-31] configured for the scenario device, example: `buttons=1,2,4`
- possible events are:
- for CEN:
-`START_PRESS` - sent when you start pressing the button
-`SHORT_PRESS` - sent if you pressed the button shorter than 0,5sec (sent at the moment when you release it)
-`EXTENDED_PRESS` - sent if you keep the button pressed longer than 0,5sec; will be sent again every 0,5sec as long as you hold pressed (good for dimming rules)
-`RELEASE_EXTENDED_PRESS` - sent once when you finally release the button after having it pressed longer than 0,5sec
- for CEN+:
-`SHORT_PRESS` - sent if you pressed the button shorter than 0,5sec (sent at the moment when you release it)
-`START_EXTENDED_PRESS` - sent once as soon as you keep the button pressed longer than 0,5sec
-`EXTENDED_PRESS` - sent after `START_EXTENDED_PRESS` if you keep the button pressed longer; will be sent again every 0,5sec as long as you hold pressed (good for rules involving dimming/volume)
-`RELEASE_EXTENDED_PRESS` - sent once when you finally release the button after having it pressed longer than 0,5sec
#### `mode` for values WEEKLY and SCENARIO (thermo Central Unit)
NOTE: lights, blinds and zones (thermostat) can be handled from personal assistants (Google Home, Alexa). In the following example `Google Assistant` (`ga="..."`) and `HomeKit` (`homekit="..."`) were configured according to the [Google official documentation](https://www.openhab.org/docs/ecosystem/google-assistant) and [HomeKit official documentation](https://www.openhab.org/addons/integrations/homekit/)
Switch iCU_3550_at1off "At least one probe in OFF" (gCentralUnit) { channel="openwebnet:bus_thermo_cu:mybridge:CU_3550:atLeastOneProbeOff" }
Switch iCU_3550_at1pro "At least one probe in PROTECTION" (gCentralUnit) { channel="openwebnet:bus_thermo_cu:mybridge:CU_3550:atLeastOneProbeProtection" }
Switch iCU_3550_at1man "At least one probe in MANUAL" (gCentralUnit) { channel="openwebnet:bus_thermo_cu:mybridge:CU_3550:atLeastOneProbeManual" }
The OpenWebNet protocol is maintained and Copyright by BTicino/Legrand. The documentation of the protocol if freely accessible for developers on the [Legrand developer web site](https://developer.legrand.com/documentation/open-web-net-for-myhome/)
